Cooperation Group Button - Revision history

ErwinL at 13:02, 17 March 2012

2012-03-17T13:02:16Z

← Older revision		Revision as of 13:02, 17 March 2012
Line 1:		Line 1:
			{{EnglishNav}}
	{{Sprachen_DE\|DE=Zustimmungsgruppentaste\|EN=Cooperation Group Button\|NL=Toestemminggroepknop}}		{{Sprachen_DE\|DE=Zustimmungsgruppentaste\|EN=Cooperation Group Button\|NL=Toestemminggroepknop}}
	~~{{EnglishNav}}~~

	== Purpose ==		== Purpose ==
	The Cooperation Group Button (ZGT) is used to give permission for a train- or shunting movement across the border of the area of responsibility.		The Cooperation Group Button (ZGT) is used to give permission for a train- or shunting movement across the border of the area of responsibility.

ErwinL at 12:45, 17 March 2012

2012-03-17T12:45:55Z

← Older revision		Revision as of 12:45, 17 March 2012
Line 1:		Line 1:
			{{Sprachen_DE\|DE=Zustimmungsgruppentaste\|EN=Cooperation Group Button\|NL=Toestemminggroepknop}}
	{{EnglishNav}}		{{EnglishNav}}

ErwinL at 07:06, 21 February 2012

2012-02-21T07:06:12Z

← Older revision		Revision as of 07:06, 21 February 2012
Line 2:		Line 2:

	== Purpose ==		== Purpose ==
	The Cooperation Group Button (ZGT) is used to give permission for a train- or shunting movement across the ~~boundary~~ of ~~operating areas~~.		The Cooperation Group Button (ZGT) is used to give permission for a train- or shunting movement across the border of the area of responsibility.

	[[File:ZGT_button.png\|200px\|thumb\|none\|Cooperation Group Button]]		[[File:ZGT_button.png\|200px\|thumb\|none\|Cooperation Group Button]]

	== Operation ==		== Operation ==
	The permission from the other dispatcher will be required in order to be able to set a train or shunting route into the other ~~operating~~ area within the same signal box.		The permission from the other dispatcher will be required in order to be able to set a train or shunting route into the other area of responsibility within the same signal box.

	This can be done in two ways: by means of [[partial routes]] or by using the [[Cooperation Group Button]] as described below.		This can be done in two ways: by means of [[partial routes]] or by using the [[Cooperation Group Button]] as described below.

	When a train or shunt route is set across the ~~boundary~~ of the ~~operating areas~~, the route can be set, however the start signal will only change to Proceed when:		When a train or shunt route is set across the border of the area of responsibility, the route can be set, however the start signal will only change to Proceed when:
	*[[Routes\|Train route]] The ZGT button is operated together with the signal end button. After operating this combination of buttons, the overlap route and train route will be locked, and so the start signal will change to Proceed.		*[[Routes\|Train route]] The ZGT button is operated together with the signal end button. After operating this combination of buttons, the overlap route and train route will be locked, and so the start signal will change to Proceed.
	*[[Routes\|Shunt route]]: The ZGT button is operated together with the signal end button. After the operation the start signal changes to the Proceed aspect.		*[[Routes\|Shunt route]]: The ZGT button is operated together with the signal end button. After the operation the start signal changes to the Proceed aspect.

ErwinL at 06:53, 21 February 2012

2012-02-21T06:53:46Z

← Older revision		Revision as of 06:53, 21 February 2012
Line 1:		Line 1:
	{{EnglishNav}}		{{EnglishNav}}
	~~{{EnglishConstruction}}~~

	== Purpose ==		== Purpose ==
	The Cooperation Group Button (ZGT) is used to give permission for a train- or shunting movement across the boundary of operating areas.		The Cooperation Group Button (ZGT) is used to give permission for a train- or shunting movement across the boundary of operating areas.

	[[File:ZGT_button.png\|200px\|thumb\|~~left~~\|Cooperation Group Button]]		[[File:ZGT_button.png\|200px\|thumb\|none\|Cooperation Group Button]]

	== Operation ==		== Operation ==
	The ZGT button is ~~used in~~ ... .		The permission from the other dispatcher will be required in order to be able to set a train or shunting route into the other operating area within the same signal box.

			This can be done in two ways: by means of [[partial routes]] or by using the [[Cooperation Group Button]] as described below.

			When a train or shunt route is set across the boundary of the operating areas, the route can be set, however the start signal will only change to Proceed when:
			*[[Routes\|Train route]] The ZGT button is operated together with the signal end button. After operating this combination of buttons, the overlap route and train route will be locked, and so the start signal will change to Proceed.
			*[[Routes\|Shunt route]]: The ZGT button is operated together with the signal end button. After the operation the start signal changes to the Proceed aspect.

ErwinL: /* Purpose */

2012-02-21T06:40:43Z

Purpose

← Older revision		Revision as of 06:40, 21 February 2012
Line 3:		Line 3:

	== Purpose ==		== Purpose ==
	The Cooperation Group Button (ZGT) is used to ~~...~~ .		The Cooperation Group Button (ZGT) is used to give permission for a train- or shunting movement across the boundary of operating areas.

	[[File:ZGT_button.png\|200px\|thumb\|left\|Cooperation Group Button]]		[[File:ZGT_button.png\|200px\|thumb\|left\|Cooperation Group Button]]

ErwinL: Created page with '{{EnglishNav}} {{EnglishConstruction}} == Purpose == The Cooperation Group Button (ZGT) is used to ... . Cooperation Group Button == O…'

2012-02-20T21:17:37Z

Created page with '{{EnglishNav}} {{EnglishConstruction}} == Purpose == The Cooperation Group Button (ZGT) is used to ... . 200px|thumb|left|Cooperation Group Button == O…'

New page

{{EnglishNav}}
{{EnglishConstruction}}

== Purpose ==
The Cooperation Group Button (ZGT) is used to ... .

[[File:ZGT_button.png|200px|thumb|left|Cooperation Group Button]]

== Operation ==
The ZGT button is used in ... .